HVAC Quizzes & Trivia
Heating, ventilation, and air conditioning (HVAC) is a combination technology of indoor and vehicular environmental comfort. Are you training to be able to properly install and maintain such systems in any environment? The quiz...
Questions: 81 | Attempts: 10210
-
Sample Question1. How many amps can a 40va, 120volt transformer with a 24volt secondary carry?
This quiz is multiple choice and fill in the blank. It is worth 25 points. You can use your notes. Do not use capital letters or puncuation marks.
Questions: 12 | Attempts: 2602
-
Sample QuestionVFD stands for what?
Test your knowledge in the Sheet Metal Shop.
Questions: 10 | Attempts: 2149
-
Sample Question___________ are used to safely carry mutiple sheets of sheet metal.
Knowledge about HVAC
Questions: 5 | Attempts: 913
-
Sample QuestionHFC STANDS FOR
This quiz is about fun and easy but next i will make harder quiz.
Questions: 3 | Attempts: 902
-
Sample Question1) what is the temperature of our body?
HVAC Questions & Answers
What is the length of the pipe to be cut of 3/4 pipe that has a 90 and a 45 at each end?
The correct answer to this question is D, 18 5/8". Knowing the correct length to cut is essential. Many pipe cutting formulas can help determine the exact extent needed to cut. If the question had more information, it could help identify the spe
What is the minimum height above the floor an appliance must be installed in a private garage?
The correct answer to this question is A, 6 feet. A person who works in HVAC and deals with housing codes would know the answer to this question. This is in correspondence with IRC G2408.3 (305.5). With all rules, there are exceptions. The exception
What length should approved hangers that support ducts not exceed (at intervals)?
The correct answer to this question is B. In HVAC (heating, ventilation, and air conditioning) there are two shapes of vertical ductwork: round and rectangular. For sheet metal ductwork, specified distances between hangers are given. With round ve
Why is a hand notcher used?
More
There are two correct answers to this question which are, A. Allows space for clean bends in metal and B. Indicates where a bend should occur when laying out and marking. This tool would be used by a person who is doing a home improvement job. Profes
Test your knowledge of the HVAC world with these "not-so-common" questions. Don't forget...  choose the "best" answer, as some questions may have multiple answers that could be correct.
Questions: 14 | Attempts: 730
-
Sample QuestionBy definition, heat...
Rudolph's review questions on air conditioning Chapter 50
Questions: 20 | Attempts: 420
-
Sample QuestionRefrigerant is a low-pressure liquid as it leaves the condenser.
STIMULATE THE BRAINS OF NEW CONVERTS
Questions: 10 | Attempts: 356
-
Sample QuestionNAME 3 OF THE 6 COMMON TYPES OF COMPRESSORS USED IN HVAC/R
With the hanging seasons it is important to keep warm in the winter and get some cool air for the summer. This therefore places some importance on understanding how to fit in heating and air conditioning equipment for...
Questions: 17 | Attempts: 229
-
Sample QuestionA manifold gauge set can be used during the evacuation of the A/C system.
Hey, friend, it really helps you.
Questions: 5 | Attempts: 224
-
Sample QuestionWhat is hvac?
HVAC Controls Final Quiz
Questions: 27 | Attempts: 152
-
Sample QuestionThe control result is not monitored for which system? (i.e. The output variable xa of the controlled system has no backward effect on the controlling equipment)
Questions: 5 | Attempts: 147
-
Sample QuestionWhat percentage can you save by changing your thermostat 1 degree?
Rudolphs review questions on heating and cooling Chap. 12
Questions: 20 | Attempts: 124
-
Sample Question100 percent antifreeze will freeze at a lower temperature than 50/50 mixture of antifreeze and water.
Questions: 26 | Attempts: 91
-
Sample QuestionFor summer cooling, temperatures of __________________ and _____% relative humidity are a frequent design average
This is your description.
Questions: 5 | Attempts: 89
-
Sample QuestionWhat has the most vampire load?
This is a quiz to assess the knowledge gained from the safety orientation
Questions: 20 | Attempts: 87
-
Sample QuestionDoes Expert HVAC have a posted Safety Policy?
This is the toughest HVAC Quiz based on Heating, Ventilation and Air Conditioning. Do you think that you have done adequate revision to tackle it or might you be in need of some practice? If you are not so sure all you need to do...
Questions: 216 | Attempts: 82
-
Sample QuestionWhat is the purpose of air conditioning?
No comment at all...
Questions: 20 | Attempts: 75
-
Sample QuestionThe primary wartime mission of civil engineering personnel is to
The following exam is produced to test knowledge of safe refrigerant handling and EPA regulations regarding the HVAC industry.
Questions: 98 | Attempts: 60
-
Sample QuestionUnder EPA's regulations, reclaimed refrigerant must meet _____standards for purity before it can be resold.
Test for cpa Hvac Critical Process Air System
Questions: 10 | Attempts: 45
-
Sample QuestionThe synthetic lubricant used with HCFC based ternary blends is
This is a quiz to assess the knowledge gained from the safety orientation
Questions: 20 | Attempts: 32
-
Sample QuestionDoes Expert HVAC have a posted Safety Policy?
See where your heating system stands.
Questions: 88 | Attempts: 21
-
Sample QuestionHow old is your furnace?
The students will answer various questions regarding basic ventilation practices.
Questions: 12 | Attempts: 20
-
Sample QuestionWhich is NOT used for verticle venilation.
